FieldQuo

Start from drawings: the drawing read

Upload a drawing set, scope sheet and photos; FieldQuo reads the sheets your quote's service needs, measures every quantity with its source and a confidence, prices it from your own rates, and recommends a price that holds your target margin.

ਇਹ ਲੇਖ ਫ਼ਿਲਹਾਲ ਅੰਗਰੇਜ਼ੀ, ਫ਼ਰਾਂਸੀਸੀ ਅਤੇ ਸਪੈਨਿਸ਼ ਵਿੱਚ ਉਪਲਬਧ ਹੈ। ਤੁਸੀਂ ਅੰਗਰੇਜ਼ੀ ਸੰਸਕਰਣ ਪੜ੍ਹ ਰਹੇ ਹੋ। Français · Español

A drawing read turns a set of drawings into a priced draft quote. It reads painting, drywall, framing, roofing, electrical, plumbing and flooring. The model never sets a price: it points at printed dimensions, schedule rows and symbols, and FieldQuo works out the quantities and prices them from your own rates.

It reads what your quote is for

There is no trade picker. The read takes the service of the quote you started it from, or the lead's service. Without either, choose one of your own services under What this quote is for. A roofing quote reads the roof plan and the elevations, never the rooms. An interior painting quote reads the inside, never the elevations.

Only the sheets your services need are sent to the AI. An electrical sheet is never paid for on a drywall quote. Cover and code sheets are never sent. Specification pages are read as text for free. The read card says how many sheets it is reading and which ones it skips.

When a set has no electrical or plumbing sheets, as in many houses, those trades read the architect's floor plans instead, and their counts are marked low confidence.

Every quantity has a source and a confidence

Where the quantity comes fromConfidence
Measured by you on the sheetHigh
Printed dimensions on a drawing with real textHigh
A schedule row (panel, fixture, door) whose printed quantity is in that rowHigh
A cell of your scope spreadsheetMedium
Symbols counted on the sheet, matched to its legend, with the quarters agreeing with the whole sheetMedium
A scanned sheet, a unit that had to be assumed, a count with no legend, a photo, or an estimateLow

Each trade has its own card: drywall by GA-214 finish level, framing in linear feet, the roof in squares sloped by the printed pitch, electrical devices, panels and circuits, plumbing fixtures, flooring by material. Two firm sources that disagree become a question for you. Check the low-confidence quantities before you send.

The first pass: measured, priced, ready to confirm

The first read now does the takeoff itself. Every sheet is classified from its title (elevation, plan, section, site, schedule, 3D view). Each elevation, plan and section is measured: wall faces are scaled off the sheet at its printed scale and paper size, rooms give their floor area and perimeter, sections give the heights. A printed dimension or a printed area always wins over a scaled one, and a printed figure on the same view checks the scale. Each quantity shows the sheet, the figures used, a confidence, and what to check.

If nothing on the set states a height, the read says so and uses a stated default (3.0 m or 9 ft) marked to verify. A surface with no quantity is listed as not priced — never left at 0 without a word.

  1. Height — each surface's area is split by working height: up to 8 ft ×1.0, 8–13 ft ×1.3, 13–17 ft ×1.6, 17–19 ft ×1.9, 19–21 ft ×2.2 (Craftsman's High Time Difficulty Factors, p. 139; above 21 ft is FieldQuo's extrapolation). The factor is on the hours only. Your rates were measured on a 9 ft room, so height is charged above that; change it in Settings → Services.
  2. Prep — by substrate and condition, as the line's own prep hours, never inside the paint rate: wash-down for previously painted surfaces, masonry primer for bare or old brick (Resene productivity tables), daily setup and clean-up for an occupied or heritage building.
  3. Access — every lift, tower and ladder is priced for the days its work takes: your own rental rates first, else Craftsman's rental table converted to your currency, marked Estimated from reference · confirm. Press Confirm or type your own price.
  4. Crew plan — days on site = hours ÷ (painters × productive hours a day), with 2, 3 and 4-painter options side by side.
  5. Priced on these assumptions — substrate, colours, heritage, site hours and occupancy are stated, not asked. Change one and the price is worked out again at once, with no AI charge.
  6. Past jobs — the draft's price and hours per sq ft against your own won and completed jobs of the same trade, with the likely reason when it is far outside.

When the quote is for more than one service — exterior and interior painting, say — the read makes a draft for each, with its own areas, access, crew plan and price, and a Create quote button each. No second read is needed.

How it is priced

  1. Your rates — your own rate card through the same engine as your typed quotes: painting, the drywall rate card (hang plus finish level) and the roofing rate card.
  2. Your services — your own services in Settings → Services whose lines are keyed to the item's measurement, with their production rate for the hours.
  3. FieldQuo suggestion — not your price yet — FieldQuo's published figures, each one shown with its source: NECA labour units for electrical (as published for commercial jobs, with the residential factor for houses), the framing price book, the drywall and flooring recipes.

An item nothing covers says No rate — add one. It is never priced at zero. Suggested lines go on the quote only when you press Put FieldQuo's suggested lines on the quote for that trade, and each one is flagged as a suggestion.

The price at your target margin

The Price at your target margin card shows the working: labour at your crew's cost rate, materials, your services' line costs, equipment, overhead, the cost, the price that holds your target, and what your own rates come to.

Overhead is this job's fair share of your month in crew time: your monthly fixed costs × (this job's crew-hours ÷ the billable crew-hours you set in Settings → Overhead). A two-week job for two people (160 crew-hours) in a 320-hour month carries half the month. Without billable hours it is split by jobs a month, and without either it is 10% of the price. The card says which one it used.

  1. When your rates hold your target, the recommendation is your rates.
  2. When they miss it, the card shows the gap and the button Add a margin adjustment line, which puts the gap on the quote as its own visible line. Your rates are never scaled behind your back.
  3. When a finished read misses the target, your owner and managers get a notification in the bell and as a push, and so does the person assigned to the quote or lead.

Changing the pricing from the chat

Tell the chat your figures, for example "my crew hangs 600 sq ft a day" or "labour costs us $42 an hour". Then press Update pricing from this conversation. It finds only figures printed in your own messages, shows what they change, and applies nothing until you press Apply to this read. The figures stay on that read and never change your settings.

What a read costs

The cost is shown before you start, held from your AI credit, and settled to what the read actually used. A read that fails is refunded in full. Fewer sheets read means a smaller charge. Each trade beyond painting adds one synthesis.

SetUsually charged
13 sheets and 10 photos, paintingabout US$1.85
The same set, one other trade reading 8 of its sheetsabout US$1.46
The same set, three tradesabout US$2.80
40 sheets, three trades reading 25 of themabout US$3.37

Reading a finished read again

FieldQuo's reader keeps improving. A finished read keeps what it found until you ask for more, so nothing changes under a quote you are working on.

  1. Measured with an older version — Read again to update appears on the read when its sheets were measured by an earlier version of the measuring step. Read again measures those sheets again and puts the project together again. The sheet readings you already paid for are kept.
  2. Read again on a finished read with nothing new reads the whole project again: every sheet, photo and measurement, with the current reader. You confirm first, and the confirm shows the credit it holds. You are charged what it actually uses, and a read that fails is refunded in full.

Reading again rebuilds the overview from the files. Changes made in the chat are replaced. Only someone who can edit quotes can read a project again, and it never happens on its own.

ਕੀ ਇਹ ਮਦਦਗਾਰ ਸੀ?